how to make a folding chair
Lightweight folding chair does not prevent a very small apartment, cottage, on a walk.
Let's make a folding chair with his hands.
Materials:
- Pine bar section 3x3 cm and 2 cm thick boards;
- Dowels (6 pieces);
- A steel rod section of 1 cm and a length of 36 cm;
- Bolts section of 0.5 cm and a length of 7 cm with nuts and washers (4 pcs);
- Screws;
- PVA glue.
Details of the chair:
- 2 long legs of the timber (90 cm);
- 2 lateral ligament of the board for the long legs (40h5 cm and 34 x 5 cm);
- Back of the board (40h7 cm);
- Two short legs of the timber (55 cm);
- 2 lateral ligament of the board for short legs (28h5 cm);
- 2 fixed beams for the seat (29 cm);
- 6 boards for the seat (34h4 cm).
Putting chair
Seat. Decompose board sanded down at intervals of 1 cm on top time supporting beams; Their outer edges are spaced apart by 34 cm at the last board seat and 28 cm on the first board. Note the position of the marker boards, flip the design of the board and attach with screws to the supporting bar. On the supporting bar between the fifth and second boards drill holes for the steel rod parallel to the planks. Thread the rod. At the level of the 2nd board also parallel boards drill holes for the screws (for mounting with short legs).
Long legs. On the outer side of each leg at the bottom of the drill head of the bolt recess therein and further drill hole for the bolt (this - for fixing with a short leg). On the inner sides of the saw blade to the slots on Which will slide steel rod ends, and closer to the top of the drill holes for the dowels. Thereafter clamped between legs perpendicular to the steel rod inserted in the slot (with the seat). At the same time shkantah attach transverse ligament 34 cm drilled with holes at the ends. Screws attach the transverse ligament (40 cm below the bolt holes) and back (at the top).
Short legs. Drill holes for bolts: Centre for fastening with long legs, and on the upper end - to secure a seat (with dimples under the bolt head on the outer edges). He shkantah fasten both transverse ligament to 28 cm: one - in the lower part, the second - above the middle.
Everything is ready for assembly. Short legs bolted to the seat, and then with long legs (get the joints). Now we can boast in front of home: here - folding chair with his hands! And already now you can relax and soak in
folding chair
Lightweight folding chair does not prevent a very small apartment, cottage, on a walk.
Let's make a folding chair with his hands.
Materials:
- Pine bar section 3x3 cm and 2 cm thick boards;
- Dowels (6 pieces);
- A steel rod section of 1 cm and a length of 36 cm;
- Bolts section of 0.5 cm and a length of 7 cm with nuts and washers (4 pcs);
- Screws;
- PVA glue.
Details of the chair:
- 2 long legs of the timber (90 cm);
- 2 lateral ligament of the board for the long legs (40h5 cm and 34 x 5 cm);
- Back of the board (40h7 cm);
- Two short legs of the timber (55 cm);
- 2 lateral ligament of the board for short legs (28h5 cm);
- 2 fixed beams for the seat (29 cm);
- 6 boards for the seat (34h4 cm).
Putting chair
Seat. Decompose board sanded down at intervals of 1 cm on top time supporting beams; Their outer edges are spaced apart by 34 cm at the last board seat and 28 cm on the first board. Note the position of the marker boards, flip the design of the board and attach with screws to the supporting bar. On the supporting bar between the fifth and second boards drill holes for the steel rod parallel to the planks. Thread the rod. At the level of the 2nd board also parallel boards drill holes for the screws (for mounting with short legs).
Long legs. On the outer side of each leg at the bottom of the drill head of the bolt recess therein and further drill hole for the bolt (this - for fixing with a short leg). On the inner sides of the saw blade to the slots on Which will slide steel rod ends, and closer to the top of the drill holes for the dowels. Thereafter clamped between legs perpendicular to the steel rod inserted in the slot (with the seat). At the same time shkantah attach transverse ligament 34 cm drilled with holes at the ends. Screws attach the transverse ligament (40 cm below the bolt holes) and back (at the top).
Short legs. Drill holes for bolts: Centre for fastening with long legs, and on the upper end - to secure a seat (with dimples under the bolt head on the outer edges). He shkantah fasten both transverse ligament to 28 cm: one - in the lower part, the second - above the middle.
Everything is ready for assembly. Short legs bolted to the seat, and then with long legs (get the joints). Now we can boast in front of home: here - folding chair with his hands! And already now you can relax and soak in